Progress and innovation of nanostructured sulfur cathodes and metal-free anodes for room-temperature Na–S batteries

• Marina Tabuyo-Martínez,
• Bernd Wicklein and
• Pilar Aranda

Beilstein J. Nanotechnol. 2021, 12, 995–1020, doi:10.3762/bjnano.12.75

Flexible freestanding MoS₂-based composite paper for energy conversion and storage

• Florian Zoller,
• Jan Luxa,
• Thomas Bein,
• Dina Fattakhova-Rohlfing,
• Daniel Bouša and
• Zdeněk Sofer

Beilstein J. Nanotechnol. 2019, 10, 1488–1496, doi:10.3762/bjnano.10.147

• the following Equation 3) and the decomposition of the electrolyte followed by the formation of a solid electrolyte interphase (SEI) layer [18][20]. The prominent anodic peak at ≈2.5 V results from the conversion of Li2S to sulfur and lithium ions (see the following Equation 4) [20]. During the

Hydrothermal-derived carbon as a stabilizing matrix for improved cycling performance of silicon-based anodes for lithium-ion full cells

• Mirco Ruttert,
• Florian Holtstiege,
• Jessica Hüsker,
• Markus Börner,
• Martin Winter and
• Tobias Placke

Beilstein J. Nanotechnol. 2018, 9, 2381–2395, doi:10.3762/bjnano.9.223

• ; prelithiation; silicon/carbon composite; solid–electrolyte interphase (SEI); Introduction Since their market launch in 1991, the energy density of lithium-ion batteries (LIBs) has increased steadily. However, further improvements in terms of power density and energy density are essential to meet the rising

• drastic volume changes during cycling hinder the formation of a dimensionally stable solid electrolyte interphase (SEI), as it is known for carbonaceous anodes, formed on the negative electrode surface from electrolyte decomposition products in the first charge/discharge cycles [18][19][20]. In the case

• , the trapping of Li inside detached Si, exposure of fresh Si to the electrolyte and breaking and reformation of the solid electrolyte interphase (SEI) layer [16][21][22][24]. All these factors contribute to an ongoing capacity loss with each cycle, leading to poor capacity retention. With higher Si

From lithium to sodium: cell chemistry of room temperature sodium–air and sodium–sulfur batteries

• Philipp Adelhelm,
• Pascal Hartmann,
• Conrad L. Bender,
• Martin Busche,
• Christine Eufinger and
• Juergen Janek

Beilstein J. Nanotechnol. 2015, 6, 1016–1055, doi:10.3762/bjnano.6.105

• discharge and charge [70]. Analogous to the lithium–sulfur batteries, the use of lithium nitrate (LiNO3) seems to improve the cyclability of Li/O2 cells as well. In publications by Liox Power Inc., it was shown that LiNO3 leads to an improved stability of the lithium electrode solid electrolyte interphase

• (SEI) formation [61]. Kang et al. showed that it also leads to an improved stability of carbon at the cathode [71]. 2.3.1.4 Differential electrochemical mass spectrometry (DEMS) studies: The electrolyte decomposition is a major drawback that made DEMS studies inevitable in Li/O2 cell research. Today

Multiscale modeling of lithium ion batteries: thermal aspects

• Arnulf Latz and
• Jochen Zausch

Beilstein J. Nanotechnol. 2015, 6, 987–1007, doi:10.3762/bjnano.6.102

• under high voltages and chemical compatible with the chosen electrode materials. Thus, additives are used in order to enhance the ionic conductivity and to improve the chemical compatibility. Also the properties of the solid electrolyte interphase (SEI) on the negative electrodes, which is essential for